2009 Ford Edge Abs No Communication

2006 Toyota Highlander Hybrid Limited. Pictures shown may vary from actual.

Pre Owned 2017 Ford Edge Titanium Suv In Duluth Dm10196c Rick Hendrick Chevrolet Duluth

From the research I did on this forum it seems like a long list of things can affect the ABS from chaffed wires to the fuse not.

2009 ford edge abs no communication. Replaced that and problem went away for about a month. The ISO 9141 network is a single-wire and is often identified as Circuit 70. 2004 - 2008 Ford F150 - ABS Light blown fuse and no communication - I have a 2005 F-150 54L with 141000 miles Well Im at my ends trying to trace down this ABS light problem.

Here we used the quick testing techniques that I. The Diagnostic Trouble Code DTC U0155 sets when the PCM does not receive the Instrument Panel Cluster Control Module message within the defined amount of time. I have no voltage or continuity to chassis on pins 2 and 10.

No problems with the Speedo and they checked the rear sensor on the Diff all was ok. Im trying to diagnose why my abs module is not communicating with the ECU in my car nor will it communicate with my diagnostic tool. Also please check out the statistics and reliability analysis of Ford Edge based on all problems reported for the Edge.

Ford wants 1200 for the repair 800 parts 400 labor. Fits the following Ford Edge Years. The Diagnostic Trouble Code DTC U0121 sets when the PCM fails to receive the Anti-lock Brake System ABS message within the defined amount of time.

No Communication with Airbag Module Multiple Solutions December 19 2017 1834 From time to time Ill get asked about an issue where the customer has no communication with the airbag control module. My friend got someone out to diagnose it who said the ABS module was fried. U0121 FORD Description.

The Powertrain Control Module PCM continuously monitors the Controller Area Network CAN for messages from the ABS. The previous numbers are for non-traction control models. My 2008 ford edge AWD was showing the ABS traction control and wrench lights on and off for a while when I would reach 60-70 mph.

According to the tech there is no communication with the ABS module. U1900 FORD Description The Anti-ock Brakes System ABS module the Powertrain Control Module and the instrument cluster communicate over the Controller Area Network CAN BusThis is a high-speed bus communication system and is not fault tolerant which means any type of intermittentloose connection between these 3 controllers will cause communication to stop. At the ends of the bus there are two terminating resistors.

They list an ABS control module for a 2003 Windstar I presume this is both the hydraulic and electronic portions MSRP price at 104952 and their discounted price of 74117 with a 200 core charge. DTC U0121 - Lost Communication With Anti-Lock Brake System ABS Control Module - Ford 2011 Ranger question. Ford Edge owners have reported 11 problems related to brake abs warning light under the service brakes category.

I even tried a different ECM with no. Now when I go highway speeds the lights come back on and car loses power occasionally. 2007 6 Cyl 35L DOHC VCT SMPI 6-Speed Automatic Transmission 6F50 Four-Wheel Drive Full Time Four-Wheel Drive Part Time Front-Wheel Drive.

I have been blowing fuse 14 which puts on the ABS light parking brake light no AC no 4x4 low no cruise control and no reverse lights. We replaced the module with a second hand one reset the engine management light and still got the same code back U0121 lost communication with ABS module. Modules communicate over the CAN High bus at a rate of 500k bitssecond whereas communication over the CAN Low bus is limited to 125k bitssecond.

Another handy thing to remember is that newer Ford vehicles are often equipped with more than one network the second being the ISO 9141 protocol. The Powertrain Control Module PCM continuously monitors the Controller Area Network CAN for messages from the Instrument Panel Cluster Control Module. 2011 Ford Edge Timing chains were replaced and after service vehicle was a no crank no communication.

I have tried several scan tools with the same result no communication. The most recently reported issues are listed below. Ford Edge ABS Control Module Part Number.

It started yesterday in snowy weather I went to the store then went back to my car and lights start flashing for ABS. Had it scanned and front left wheel speed sensor showed no signal. The testing methods shown in this video can be used in any no communication conditionIn this video we are working on a 2001 Volkswagen Passat.

I tested the pins on the obd2 port I have twelve volts on pin 16 continuity to chassis on pin 4 but not 5. The numbers are 132772 and 93763 for traction control. I m working on ford 1999 e150 the abs light is on i have snap on scanner there is no comunication to the scanner checked - Answered by a verified Ford Mechanic We use cookies to give you the best possible experience on our website.

There is no module-to-module communication on this network. Code U0121 indicates the ABS module is not receiving or transmitting messages on the CAN bus.

E 3hrxfn4ywncm